How To Install Blade Guard On Craftsman Table Saw
Installing a blade guard on your Craftsman table saw is an important safety precaution. This video will show you how to do it quickly and easily.
A properly installed blade guard protects your fingers and hands from being injured by the spinning blade. This is a straightforward process and this article will walk you through it step by step.
The installation will take only a few minutes and you can then use your table saw without worry knowing your fingers are safe.
How To Install Blade Guard On Craftsman Table Saw? Step By Step
These are the steps for installing a blade guard to your Craftsman tablesaw.
- Unplug the saw’s power source.
- Remove the throat plate by unscrewing the two screws that hold it in place.
- Raise the blade to its maximum height.
- Attach the blade guard to the bracket by attaching it first to the back side of the table saw (under the tabletop). Then, slide the guard onto the bracket. I Use Craftsman 089037007700 Blade Guard.
- Use the two screws from Step 2 to fix the bracket in place.
- Replace the throat plate and screw it into place.
- Plug the saw back in and test the blade guard by moving it up and down to make sure it is secure.
What Is The Purpose Of A Blade Guard?
The primary reason for the blade guard is to prevent the user from accidentally cutting themselves. This can be done in several ways, including by making it difficult or impossible to reach the edge of the knife.
The second most important function of a blade guard is to keep debris out of the knifes handle and/or mechanism. A well-designed guard will provide you with a safe place to rest your hands while you use the knife.
There are other reasons why you might want a blade guard. Some people use knives as eating tools. If the guard gets in the way of this, they may not use the knife at all.
Other people just dont like working with sharp blades near them. Instead, they prefer duller blades. Some people feel safer working with a guard in place. Others do not. Each to his own.
Safety Tips
Cutting with the wrong tool can cause serious injury. This includes using a circular saw when a jigsaw is more appropriate. The circular saw is not used to cut across the grain, but for ripping lumber. Always use the correct tool for the job.
When possible, use an anti-kickbackpawl. Anti-kickback pawls are found on most power miter saws. These devices help reduce kickbacks. Kickbacks are when the spinning blade strikes something while it is moving away from the workpiece.
The blade will spin toward the operator when it strikes the object with its force. This action is prevented by an anti-kickback device.
- The first step to safely using a table saw is to set up the machine correctly. Before you turn on the motor, make sure that all parts are aligned correctly.
- Place a piece of scrap material against the fence so that the blade will have a clear path to travel through. Before beginning any cuts, make sure the blade is free of obstructions.
- Make sure the blade guard is in place. It may be attached permanently or removable. It doesn’t matter what, a blade protector is better than a regular shield because it lowers the chance of getting an eye injury.
- Attach the blade guard to the side of the table saw. It can be bolted down or screwed into place.
- Turn on the motor and adjust the height of the blade guard. Adjusting the height allows you to raise or lower the guard without having to remove it.
- Adjust the angle of your blade guard. Depending on the location you intend to cut, angle the guard forward or backward. For example, if youre making a horizontal cut, the guard should be angled slightly forward.
- Turn off the motor and test the blade guard. Verify that there are no loose parts. Check to make sure the blade guard is in the right place. If necessary, tighten bolts and screws.
You should clean a permanent blade guard regularly. If it is not permanent, clean it occasionally.
Conclusion
Blade guards help prevent injury from flying objects. However, you must take precautions to ensure that the blade stays securely fastened to the saw. Follow the steps above when setting up your table saw.
FAQ,s
How Does A Blade Guard Work?
Blade guards are usually made of metal, plastic, or wood. Metal guards are used primarily for industrial applications.
Although plastic guards tend to be cheaper than metal ones, they are more likely to fall apart. Wooden guards tend to be less expensive than other types. There are many sizes and shapes available for wood guards.
One common type of wood guard is called a fence. Fences are designed to hold the blade in place during operation. Another popular type of guard is called a pawl.
Which Is The Biggest Blade That Can Be Used On A Saw?
There are two sizes: the 30 cm and the 36 cm. The smaller size is best for small jobs, while the larger one is for more heavy-duty tasks such as framing.
When wood particles are caught between the teeth and fence, they can cause splintering. To avoid splintering, make sure the fence is parallel to the blade.
You should also try to make straight lines. A router is better for cutting curves. Best Large Blade 14BLADEST.
Why Is My Table Saw Missing An Auto-stop Function?
Most newer table saws do not include an auto-stop function. Instead, they have a safety device called a brake system. This feature automatically stops the blade when it encounters an obstruction.
What Happens Next If You Finish A Piece Of Wood But There Are Still Parts?
When you finish cutting a piece of wood, youll notice that there are still some remaining parts left. The last piece of wood remains stationary after the saw has finished cutting.
The remainder of the piece moves past the blade creating a ragged edge.
